Core Electronic Parts Kit for VORON 2.4r2 3D Printer
This kit delivers every electrical and wiring component you need to build a VORON 2.4 Rev 2 (r2) 3D printer — curated to match the official VORON Design BOM. Ships from our Seattle-area warehouse — no waiting weeks for international freight.
This is the core electronics bundle — it intentionally excludes components you will likely customize: the controller board, stepper drivers, Raspberry PI, hot end. A selection of add-on items is available separately.
Included parts:
| Part description | Qty | Notes |
|---|---|---|
| Electronics | ||
| Omron D2F-01L MicroSwitch | 2 | 100mA 30V with lever for X and Y stops |
| Omron D2F-5 MicroSwitch | 1 | 250V 5A without lever for Z stop |
| 50x50x15mm Centrifugal Fan (24V) | 1 | |
| 40x40x10mm Axial Fan (24V) | 1 | |
| 60x60x20 Axial Fan (24V) | 3 | |
| ZF Rocker Switch DPST 16A | 1 | |
| IEC320-C14 Power Inlet (not filtered) | 1 | Compatible module with no filter is used |
| 8A Fuse 250V 5x20mm | 1 | |
| Flat Head Self Tapping Screw #4 x 3/8" | 2 | |
| Mean Well LRS-200-24 PSU | 1 | |
| Mean Well RS-25-5 PSU | 1 | |
| Omron G3A-210B-DC5-24 SSR | 1 | |
| BAT85 Diode | 1 | |
| C13 Power Cord | 1 | |
| Thermal Fuse Set | 1 | Includes: 125°C 15A 250V Fuse, ring crimp terminal, connector, screws |
| Misc | ||
| Tesa Wire Loom Harness Tape | 1 | |
| Cables | ||
| Nylon Cable Ties 4" | 50 | |
| Spade Crimp Terminal | 30 | |
| Insulated QuickConnect Crimp Receptacle | 10 | |
| 20AWG Flexible Silicone wire - 7m spool | 1 | |
| 24AWG Flexible Silicone wire - 9m spool | 7 | |
| 18AWG Wire set | 1 | 4ft each White/Green/Red; 8ft Black |
| Wago 221-415 5-way Splices | 3 | |
| JST XHP-2 Housing | 6 | |
| JST XHP-3 Housing | 6 | |
| JST XHP-4 Housing | 7 | |
| JST Crimp Pin SXH-001T-P0.6 | 50 | |
| MicroFit3 Male Pin | 50 | |
| MicroFit3 Connector Plug 4 Position | 5 | |
| MicroFit3 Connector Plug 3 Position | 1 | |
| MicroFit3 Connector Plug 2 Position | 6 | |
| MicroFit3 Female Pin | 50 | |
| MicroFit3 Connector Receptacle 4 Position | 5 | |
| MicroFit3 Connector Receptacle 3 Position | 1 | |
| MicroFit3 Connector Receptacle 2 Position | 6 | |
| MLX Power Receptacle 3 Position | 1 | |
| MLX Power Plug 3 Position | 1 | |
| MLX Male Pin | 6 | |
| MLX Female Pin | 6 | |
Core kit option does not include Controller Board; Stepper Drivers; Display; Raspberry Pi; SD Card; Hot end; Inductive probe
Photos show representative content. The BOM table above is the definitive parts list.
Cable chains are not included in this kit and are available separately.
Power switch and inlet module are compatible with filtered mains option of the printed inlet panel.
This is not a plug-and-play kind of a kit. Intended for experienced makers building from the VORON Design BOM.
At our discretion, we will provide reasonable quantities of extra parts on demand, free of charge, for up to 60 days after the kit purchase. Do not hesitate to contact us if you lost a screw or broke a crimp connector.
We are doing our best to provide all parts in the quantities listed, but mistakes can happen. In case if some items are miscounted, please contact us within 60 days after the purchase and we’ll ship missing items to you free of charge.
Unused and fully intact kit in its original condition can be returned up to 30 days after the purchase.
- VORON 2.4 r2 electronics bundle / electronics package
- Klipper firmware / Klipper-compatible
- CoreXY printer electronics
- Mean Well PSUs
- 24V electronics kit
- Open-source 3D printer build
- VORON Design BOM compliant
- US stock / ships from USA / US warehouse
- Self-sourced VORON kit alternative
Compatible Printer
This kit is designed specifically for the VORON 2.4 r2 (all build sizes: 250, 300, and 350mm). It is not intended for VORON Trident or VORON V0, which have different electronics requirements. Check our Trident kits if you are building a Trident.
Built for Experienced Makers
The VORON 2.4 is an advanced, open-source CoreXY 3D printer designed for DIY builders. This kit requires crimping connectors, running wiring, and configuring Klipper firmware. It is not a plug-and-play solution — and that's the point. If you're ready to build, we're here to support you.
DigMach Build Support
- Ships from Seattle — most US orders arrive in 3–7 business days (please allow up to 5 additional business days for handling)
- Free shipping on orders over $149 — this kit qualifies
- 60-day extras policy: Lost a screw or broke a crimp connector during your build? Contact us within 60 days and we'll send replacements free of charge
- Miscounting guarantee: If any item in your kit is miscounted or missing, contact us within 60 days for free replacement shipping
- 30-day returns: Unused kits in original condition accepted within 30 days of purchase
Frequently Asked Questions
What controller board should I use with this electronics kit?
This kit does not include a controller board, as most builders prefer to choose their own. The most popular options for the VORON 2.4r2 are the BigTreeTech Octopus and FYSETC Spider. Both are available in our Controllers collection.
Is this kit compatible with the VORON Trident or VORON V0?
No. This kit is built to the VORON 2.4 r2 BOM specifically. The Trident and V0 use different PSU configurations, endstops, and wiring layouts. See our Trident kits for a Trident-specific electronics bundle.
Does this kit include cable chains?
Cable chains are not included but are available separately in our store. Browse our VORON Kits collection for cable chain options sized for the VORON 2.4.
How long does shipping take, and where does this ship from?
All orders ship from our Seattle-area warehouse in Washington State. This item requires additional handling and ships within 5 business days of your order. Orders over $149 qualify for free domestic shipping.
What if I'm missing a part or lose a connector during the build?
We've got you. Within 60 days of your purchase, contact us and we'll ship reasonable quantities of replacement parts — crimp pins, screws, connectors — at no charge. Just reach out via our Contact page.
Do I need a Raspberry Pi for this build?
A Raspberry Pi (or compatible SBC) is required to run Klipper firmware, which the VORON 2.4r2 is designed for. It is not included in this kit. The Raspberry Pi CM4 and BTT CB1 are popular choices. Check current availability in our store.